First shots with my new luminous toys!

I could not wait one more minute to using my new Light Painting toys so that, as soon as I got off work last Friday I headed to a park located next to Hammersmith Bridge. Girlfriend and some patient friends joined me and my new light painting gear to take a bunch of shots. Before the show, we had 2 or 3 pints of beer each to increase the creativeness slightly! hehe.

It was freezing and windy (maybe one more pint would have helped with this??) so we did not find the most ideal conditions to spend as much time as I would have wanted to, but anyway, I started to see the potential of what I just built and it is quite promising. I believe this summer this will be a common plan for me and friends, and the good point is that they seem to enjoy it too.

We were 4 people and in most of the pictures every one of us contributed in some way, either moving the lights around, checking the stop watch, enhancing the background with a torch and so on and so forth.

Blog___DIY_Light_Rails_Gear_0043  Blog___DIY_Light_Rails_Gear_0044 Blog___DIY_Light_Rails_Gear_0045  Blog___DIY_Light_Rails_Gear_0046

The pictures were taken in the darkest spot we could find in the area, but as you can see the background is still too bright, meaning that I could not go slower than 1 minute of shutter speed without ruinning the frame! This time does not give too room for most ideas so next week I will try to find a more suitable location. Fingers crossed for the weather being a bit more thankful, hehe.

DIY your own Light Painting Gear for creating Light Orbs

I have always felt attracted by Light Painting. In my opinion this is possibly one of the most creative photographic techniques of them all. Some would say that photography in general can be as creative as you want it to be, but here is my point:

When you take a picture, you prepare a mixture of creativeness, originality and imagination in order to get the most of the environment elements available in front of you. You decide, you press the shutter and there you go, your possible new masterpiece is ready to develop! Light painting goes one step further and, apart from all the previous, the photographer adds elements that do not actually exist in the frame!! He creates the picture as if he were a painter, but with the key difference that painters use paint whereas we use LIGHT, and light and how to control it is what photography is all about.

For further information check this out.

This technique is not new to me since I have played with it every now and then in the past, but I was totally self taught until I attended the last 9th of February to a Meetup group about Light Painting, precisely about how to create Light Orbs and Light Rails. I enrolled to this event since I had tried to make these child´s game Light Obrs or Light Spheres and all I obtained was a perfectly crappy bi-polar ellipses bent towards every possible side, hehe.

In the meetup we were showed how to improve our technique to create good Orbs, but that is something I am not going to explain right now. However, since it is a tricky business that not only requires to know the theory but to practise it a lot, I will dedicate a future post just for that, promised!

Apart from it, the most interesting stuff I learnt during the nearly 4 hours the meetup lasted for was the “How To” part of it. The meetup coordinators, Shiu Bond Whan and Dion Hitchcock, and organiser Alex Laberge kindly explained in detail how to build our own. Amazingly enough, everything was LED based hand made stuff. The ones who know me are aware of how much I love to attempt building things of this kind and so having that gear within my equipment suddenly  became a “need”.

After the meetup I contacted Shiu asking him the exact materials he bought on eBay since not all LEDs are ideal for the job. The colours are important since some colours are not suitable at all, for example red (although you can find some expensive ones that would work).

There are two jigs to build and here I put a list of the materials required for each:

Materials for LIGHT ORBS (difficulty: 5 out of 10 // time: 60 minutes // price: between £7 and £9):

Once you know the materials, lets start building the LIGHT ORBS jig:


STEP 1: Test that the 30 LEDs light string functions correctly:

Blog___DIY_Light_Orbs_Gear_0001  Blog___DIY_Light_Orbs_Gear_0002

STEP 2: Stick sellotape to a table (sticky side upwards)


STEP 3: One by one stick the 30 LEDs to the adhesive of the sellotape, leaving roughly 3 cm between LEDs:

Blog___DIY_Light_Orbs_Gear_0004  Blog___DIY_Light_Orbs_Gear_0005  Blog___DIY_Light_Orbs_Gear_0006  Blog___DIY_Light_Orbs_Gear_0007  Blog___DIY_Light_Orbs_Gear_0008  Blog___DIY_Light_Orbs_Gear_0009

STEP 4: Once the 30 are attached to the sellotape, cover them with another layer (sticky side against sticky side)

Blog___DIY_Light_Orbs_Gear_0012  Blog___DIY_Light_Orbs_Gear_0011  Blog___DIY_Light_Orbs_Gear_0010

STEP 5: At this point you have a tidier LED string, easier to manipulate. Cut the wire with a cutting pliers as follows:


STEP 6: Reserve the battery holder for later and focus on the LED string. Grab the LED on one of the sides and start rolling the rest of the LEDs over it:

Blog___DIY_Light_Orbs_Gear_0015  Blog___DIY_Light_Orbs_Gear_0016  Blog___DIY_Light_Orbs_Gear_0017

STEP 7: Once you have formed a swirl with all the LEDs hold everything in position with sellotape, covering the outer LEDs and the bunch of wires with several loops until you get a solid structure:

Blog___DIY_Light_Orbs_Gear_0018  Blog___DIY_Light_Orbs_Gear_0019  Blog___DIY_Light_Orbs_Gear_0020

STEP 8: Unsolder the remains of the original thin wires from the switch board inside the battery holder as follows:

Blog___DIY_Light_Orbs_Gear_0022  Blog___DIY_Light_Orbs_Gear_0023

STEP 9: With the help of a heavy-duty soldering iron (do not use good quality one for this task) resize the hole until it is big enough to pass the new wires (audio cable) through it. Take into account that the cable must pass tight through the whole, to avoid the solder joints to break when the cable is pulled out (if the cable get loose you will need to glue it to strengthen it so be careful not oversizing the hole too much)

Blog___DIY_Light_Orbs_Gear_0024  Blog___DIY_Light_Orbs_Gear_0025

STEP 10: Pass the two cores of the cable through the whole and leave excess of wire that allows you to solder it comfortable to the pads on the switch board


STEP 11: Solder each wire to any of the two pads (at this point the polarity is not important)

Blog___DIY_Light_Orbs_Gear_0028  Blog___DIY_Light_Orbs_Gear_0029  Blog___DIY_Light_Orbs_Gear_0030

STEP 12: Stripe about 1cm  off the other end of the cables (unconnected for now). Put the switch in the ON position and try the polarity. When the LEDs light up, remember that polarity and solder the audio cable to the LED thin wires accordingly. Once soldered, cover it with heatshrink tube (you can buy it from any hardware stores) and apply heat to make it hug the solder joint. If you do not have access to heatshrink tube, insulating tape can be used instead.

Blog___DIY_Light_Orbs_Gear_0031  Blog___DIY_Light_Orbs_Gear_0032 Blog___DIY_Light_Orbs_Gear_0032

STEP 13: Hold the wires in position over the LED “bulb” using sellotape. Give it a good amount of turns. The more sellotape you put and tension you apply here, the better, stronger and more resistant will your wiring and soldering be. This means, fewer repairs would be required (if they ever break). Do not rush, do things properly.

Blog___DIY_Light_Orbs_Gear_0034  Blog___DIY_Light_Orbs_Gear_0035  Blog___DIY_Light_Orbs_Gear_0036

STEP 14: Switch on your new toy and verify that it works correctly:

Blog___DIY_Light_Orbs_Gear_0037  Blog___DIY_Light_Orbs_Gear_0038  Blog___DIY_Light_Orbs_Gear_0039

I have made myself 4 different colours. The green one is only composed by 20 LEDs so, in order to get as good results as with the other colours I need to play a bit more with my camera settings or to choose a different and darker location to shot in.

Blog___DIY_Light_Orbs_Gear_0042  Blog___DIY_Light_Orbs_Gear_0041

Now, some quick test shots at home at f13 and 15 seconds of shutter speed:

Blog___DIY_Light_Orbs_Gear_0043  Blog___DIY_Light_Orbs_Gear_0046  Blog___DIY_Light_Orbs_Gear_0047  Blog___DIY_Light_Orbs_Gear_0048


I want to thank again to Shiu Bond Wan and Dion Hitchcock for their time and priceless help!!

Thank you